Nous utilisons des cookies pour vous fournir le meilleur service possible. Si vous continuez la navigation sur le site, vous acceptez l'utilisation des cookies.

LED Fog Lights BMW K1600GT incl. MotoBozzo-Switch - 1155

LED Fog Lights BMW K1600GT incl. MotoBozzo-Switch
plus de photos:
Prix
 
399,00*
Poids d'expédition: 0.8 kgs
Quantité / Version
Montant Total
Prix par piéce:
Prix de base:
Stock
Delivery Time: 1 Week
Description
LED Fog Lights with VA Brackets
- including wiring harness with MotoBozzo-Switch for mounting on existing crash bar with lamp receptacle or original BMW light bar


Existing boring at the crash bar / BMW light bar (see photos) will be used, therefore, drilling is not required.

The light set comes completely with pre-wired harness, MotoBozzo switch, cables, clamps and mounting hardware - but without crash bars!

The LED fog lamps have a power consumption of only 13 watts each and have an E-Mark / approval. ABE is also not necessary, since the operation of two fog lamps generally allowed.

The LED fog lamps used here each have a separate external control device and are equipped with generously dimensioned aluminum heat sink on the back. Thus, this LED bulb is quite small and well protected against heat, the lens distributes the light beam perfectly!
All screws and lamp holders are made VA stainless steel.

The manufacturer writes:
A new type LED Light Projector with outstanding lighting technology. Very small and compact design with a very high light output. This fixture is specially designed for vehicles and motorcycles where space and weight is critical - including an attractive chrome frame.

• Aaluminum housing with black powder coated and patterned.
• Corrosion protection for 480 hours salt spray
• Waterproof connector
• Extremely compact design
• Hardened plastic disc
• ECE and SAE approved
• Development and production according to TS 16949 standard

Including MotoBozzo switch for switch-free installation - no reprogramming of the control unit and no additional switch is required!

Function of the MotoBozzo-Switch
With switching-on the ignition the lamps are automatically switched on.
Now, the lamps can be switched on and off by applying the flash-light two time (click-click).

This short light horn signal for switching is, of course, used before departure and during the trip without oncoming traffic.

Since the lamps automatically operate in parallel with the ignition, shifting is according to our experience almost never necessary ...
A 5 mm green LED-display shows the operating condition.
In case it is requested to have the lamps switched off when igniting, just detach the lilac wire and attach the green wire instead.

In this case, however, the lights must be switched on manually at each start up. Since this might easily been "forgotten", we prefer / recommend to operate the circuit in the delivery condition.

The supplied wiring harness is prefabricated and fits very precisely in order to ease the attachement. In practice this means that only 4 wires must be connected according to the illustrated instructions. There are 2 cables (positive and negative) to be connected directly to the battery. And 2 cables from the electronics are to be soldered on the headlight connector (found behind the right front speaker).

After installation you will quickly see that during the day you are much better seen and therefore drive more securely. At night you will notice that beginning from the front tire.
informations complémentaires
Question sur le produit?
Vous avez une question sur le produit?
Votre adresse e-mail:
Votre question:
S'il vous plaît entrer ces lettres
captcha
Description
informations complémentaires
Question sur le produit?
LED Fog Lights with VA Brackets
- including wiring harness with MotoBozzo-Switch for mounting on existing crash bar with lamp receptacle or original BMW light bar


Existing boring at the crash bar / BMW light bar (see photos) will be used, therefore, drilling is not required.

The light set comes completely with pre-wired harness, MotoBozzo switch, cables, clamps and mounting hardware - but without crash bars!

The LED fog lamps have a power consumption of only 13 watts each and have an E-Mark / approval. ABE is also not necessary, since the operation of two fog lamps generally allowed.

The LED fog lamps used here each have a separate external control device and are equipped with generously dimensioned aluminum heat sink on the back. Thus, this LED bulb is quite small and well protected against heat, the lens distributes the light beam perfectly!
All screws and lamp holders are made VA stainless steel.

The manufacturer writes:
A new type LED Light Projector with outstanding lighting technology. Very small and compact design with a very high light output. This fixture is specially designed for vehicles and motorcycles where space and weight is critical - including an attractive chrome frame.

• Aaluminum housing with black powder coated and patterned.
• Corrosion protection for 480 hours salt spray
• Waterproof connector
• Extremely compact design
• Hardened plastic disc
• ECE and SAE approved
• Development and production according to TS 16949 standard

Including MotoBozzo switch for switch-free installation - no reprogramming of the control unit and no additional switch is required!

Function of the MotoBozzo-Switch
With switching-on the ignition the lamps are automatically switched on.
Now, the lamps can be switched on and off by applying the flash-light two time (click-click).

This short light horn signal for switching is, of course, used before departure and during the trip without oncoming traffic.

Since the lamps automatically operate in parallel with the ignition, shifting is according to our experience almost never necessary ...
A 5 mm green LED-display shows the operating condition.
In case it is requested to have the lamps switched off when igniting, just detach the lilac wire and attach the green wire instead.

In this case, however, the lights must be switched on manually at each start up. Since this might easily been "forgotten", we prefer / recommend to operate the circuit in the delivery condition.

The supplied wiring harness is prefabricated and fits very precisely in order to ease the attachement. In practice this means that only 4 wires must be connected according to the illustrated instructions. There are 2 cables (positive and negative) to be connected directly to the battery. And 2 cables from the electronics are to be soldered on the headlight connector (found behind the right front speaker).

After installation you will quickly see that during the day you are much better seen and therefore drive more securely. At night you will notice that beginning from the front tire.
Vous avez une question sur le produit?
Votre adresse e-mail:
Votre question:
S'il vous plaît entrer ces lettres
captcha